Assessment Type : Practice Worksheets : End of UO 1c Use of different Types of lines. "Lettering" : in LMS 

https://documentcloud.adobe.com/link/track?uri=urn:aaid:scds:US:9a39933c-e7a4-48fa-9761-6c8383aeae0a

Comments

  1. UnknownMarch 16, 2021 at 10:12 PM

    The simultaneous use of chain and parallel dimensioning results in combined dimensioning

    ReplyDelete
  2. PRITHVIRAJ PATILApril 25, 2021 at 2:58 AM

    Sir not open this

    ReplyDelete
    Replies
    1. S K MURABATTEApril 25, 2021 at 7:24 AM

      https://documentcloud.adobe.com/link/track?uri=urn:aaid:scds:US:9a39933c-e7a4-48fa-9761-6c8383aeae0a

      Delete
  3. UnknownApril 25, 2021 at 5:45 AM

    There is no opening of link

    ReplyDelete
    Replies
    1. S K MURABATTEApril 25, 2021 at 7:24 AM

      https://documentcloud.adobe.com/link/track?uri=urn:aaid:scds:US:9a39933c-e7a4-48fa-9761-6c8383aeae0a

      Delete

Post a Comment

Popular posts from this blog

Cross hairs, Co-ordinate System, GRID & SNAP

Status bar : Status bar accommodates following buttons, namely, 'SNAP, GRID, ORTHO etc......'. Click on 'GRID' button on status bar and one will see small dots appear in the drawing area. The drawing area provides cross hairs, which are the two lines at right angles and the crossing point is a point of selection. The cross hairs are connected to mouse and the crossing point can be scrolled up-down and right-left. The two black arrows in the left corner of the drawing area indicate user the X and Y direction. This icon is called ' co-ordinate system icon's. The present co-ordinate system is the 'World Co-ordinate System' ( WCS). WCS / World Co-ordinate System : WCS or World Co-ordinate System is a basic co-ordinate system that is default in the CAD software. GRID :  An area covered with regularly spaced dots or lines to aid drawing. The grid spacing is adjustable. The grid dots are never plotted. Grid shall show one the dots at a specified distance. One c
Read more

Layout Settings

Basic setup of drawing : Layout preparation requires following commands.  ● Units : The format for display co-ordinates and measurement units. (i) Decimal (ii) Engineering (iii) Architectural (iv) Fractional (v) Scientific Use Units menu to change the units to Engineering or Architectural type. ● Limits The command LIMITS sets and controls the drawing boundaries. At the command prompt, type LIMITS and enter ON/OFF/<Lower left corner> <current> : [ Possible actions : (1) Specify a point (2) type ON and enter (3) type OFF and enter (4) press enter to terminate the LIMITS command] The LIMITS is used to set up the area of a drawing started from scratch or to change the area settings of an existing drawing. The default drawing area is 12 X 9 ( in inches). The drawing area provides cross hairs, which are the two lines at right angles and the crossing point is a point of selection. The cross hairs are connected to mouse and the crossing point can be scrolled up-down and right-left
Read more

Modify Menu : Part I

2. The MODIFY Menu The MODIFY Menu contains sub-menus or commands to modify the drawn object. 2.1 TRIM : TRIM command cuts the portion of the object, which extends beyond another object. At the command prompt, enter TRIM Select cutting edges : (Projmode = UCS, Edgemode = No extend) Select objects: Use an object selection method <Select object to trim> / Project / Edge / Undo : Select an object, enter an option, or press enter. 2.2 ERASE : ERASE is used for erasing or deleting the objects from the drawing. At the command prompt, enter ERASE Select objects : Use an object selection method. ● Other Methods of ERASING the objects : 1] Selecting a single object 2] Window Selection      A] Left to right selection window      B] Right to left selection window ( Crossing) 2.3 COPY : With COPY command one can copy set of objects to a different location. At the command prompt, enter COPY Select objects : Use an object selection method < Base point or displacement > /Multiple : Specif
Read more